High-pressure ratio centrifugal compressors are applied to turbochargers and turboshaft engines because of their small dimensions, high efficiency, and wide operating range. Such a high-pressure ratio centrifugal compressor has a transonic inlet condition accompanied with a shock wave in the inducer portion. It is generally said that extra losses are generated by interaction of the shock wave and the boundary layers on the blade surface. To improve the performance of high-pressure ratio centrifugal compressor, it is necessary to understand the flow phenomena. Although some research works on transonic impeller flow have been published, some unknown flow physics are still remaining. The authors designed a transonic impeller, with an inlet Mach number about 1.3, and conducted detailed flow measurements by using laser doppler velocimetry (LDV). In the result, the interaction between the shock wave and tip leakage vortex at the inducer and flow distortion at the downstream of inducer were observed. The interaction of the boundary layer and the shock wave was not observed. Also, computational flow analysis was conducted and compared with experimental results.

Issue Section:
Technical Papers
Keywords:
aerodynamics, computational fluid dynamics, transonic flow, Mach number, compressors, turbines, laser velocimetry, Doppler measurement
Topics:
Aerodynamics, Blades, Compressors, Computational fluid dynamics, Flow (Dynamics), Impellers, Leakage, Mach number, Shock waves, Vortices, Suction, Compressor impellers, Pressure
1.
Rodger, C., 1998, “The Centrifugal Compressor Inducer,” ASME Paper No. 98-GT-32.
2.
Pak, H., Krain, H., and Hoffman, B., 1993, “Flow Field Analysis in a High Pressure Ratio Centrifugal Compressor,” AGARD Meeting.
3.
Krain, H., Hoffman, B., and Pak, H., 1995, “Aerodynamics of a Centrifugal Compressor Impeller with Transonic Inlet Conditions,” ASME Paper No. 95-GT-97.
4.
Eisenlohr, G., Dalbert, P., Krain, H., Proll, H., Richter, F., and Rohne, K., 1998, “Analysis of the Transonic Flow at the Inlet of a High Pressure Ratio Centrifugal Impeller,” ASME Paper No. 98-GT-24.
5.
Krain, H., Karpinski, G., and Beversdorff, M., 2001, “Flow Analysis in a Transonic Centrifugal Compressor Rotor Using 3-Component Laser Velocimetry,” ASME Paper No. 2001-GT-0315.
6.
Ibaraki, S., Higashimori, H., and Matsuo, T., 2001, “Flow Investigation, of a Transonic Centrifugal Compressor for Turbocharger,” 23rd CIMAC.
7.
Hayami, H., Umemoto, A., Itoh, K. and Kawaguchi, N., 1995, “Effects of Camber of Inducer on the Performance of a Transonic Centrifugal Compressor,” ASME FED-Vol. 222, Fluid Machinery.
8.
Hah, C., and Krain, H., 1999, “Analysis of Transonic Flow Fields Inside a High Pressure Ratio Centrifugal Compressor at Design and Off Deign Conditions,” ASME Paper No. 99-GT-446.
9.
Furukawa, M., Inoue, M., Saiki, K. and Yamada, K., 1998, “The Role of Tip Leakage Vortex Breakdown in Compressor Rotor Aerodynamics,” ASME Paper No. 98-GT-239.
10.
Dawes, W. N., 1987, “Application of a Three-Dimensional Viscous Compressible Flow Solver to a High-Speed Centrifugal Compressor Rotor—Secondary Flow and Loss Generation,” I Mech E Conf. Publ., No. C261/87.
11.
Baldwin, B., and Lomax, H., 1978, “Thin Layer Approximation and Algebratic Model for Separated Turbulent Flows,” AIAA Pap., No. 78–257.
Copyright © 2003
 by ASME
You do not currently have access to this content.