Abstract

A rig with two orthogonal, servo-hydraulic actuators based around a universal testing machine provides a flexible, low-cost biaxial testing facility and has been used to examine the influence of direct biaxial stress on deformation and crack propagation, particularly in high cycle fatigue. In principle, a balanced, horizontal loading axis is supported independently of the specimen, coincident with its axis, on low-stiffness springs to accommodate the vertical movements of the horizontal loading train; vertical and horizontal force variations, including inertial effects, are negligibly small. For 0 to 50 kN equibiaxial fatigue loading on 6-mm steel plate specimens containing center cracks up to 35 mm in length, a frequency response in excess of 20 Hz was obtained from a single 45 litre/min hydraulic pump. The paper discusses problems encountered in design and operation and recommends further improvements. Finite element stress analysis was used to help derive a cruciform geometry specimen adaptable to compressive and through-zero loading with a satisfactory biaxial stress field over the center section. Fatigue tests on mild steel plate indicated the significant role of specimen geometry in biaxial crack growth studies and showed a decrease in crack growth rate in equibiaxial tension compared with uniaxial tests but a substantial increase during Mode II loading (pure shear, or equibiaxial tension-compression). For angled crack studies tensile crack opening displacements during biaxial crack growth result in rotational relative movement of the two loading axes, which obviate the use of fixed axis systems because of imposed constraints.

References

1.
Paris
,
P. C.
and
Sih
,
G. C.
, “
Stress Analysis of Cracks
,” in
Symposium on Fracture Toughness Testing and Its Application
, STP 381,
American Society for Testing and Materials
,
Philadelphia
,
1965
, pp.
30
-
81
.
2.
Hilton
,
P. D.
, “
Plastic Intensity Factors for Cracked Plates Subjected to Biaxial Loading
,”
International Journal of Fracture
, Vol.
9
, No.
2
,
1973
, pp.
149
-
156
.
3.
Adams
,
N. J. I.
, “
Some Comments on the Effect of Biaxial Stress on Fatigue Crack Growth and Fracture
,”
Engineering Fracture Mechanics
 0013-7944, Vol.
5
, No.
4
,
1973
, pp.
983
-
991
.
4.
Miller
,
K. J.
and
Kfouri
,
A. P.
, “
An Elastic-Plastic Finite Element Analysis of Crack Tip Fields Under Biaxial Loading Conditions
,”
International Journal of Fracture
, Vol.
10
, No.
3
,
1974
, pp.
393
-
404
.
5.
Lee
,
J. D.
and
Liebowitz
,
H.
, “
The Nonlinear and Biaxial Effects on Energy Release Rate, J-Integral and Stress Intensity Factor
,” research report,
George Washington University
, Washington, D.C.,
03
1977
.
6.
Kebler
,
J. J.
and
Roberts
,
R.
, “
The Effect of Biaxial Stresses on Fatigue and Fracture
,”
Journal of Engineering for Industry, Series B of the Transactions of the ASME
, Vol.
92
,
11
1970
, pp.
727
-
734
.
7.
Erdogan
,
F.
and
Ratwani
,
M.
, “
Fracture of Cylindrical and Spherical Shells Containing a Crack
,”
Nuclear Engineering and Design
 0029-5493 https://doi.org/10.1016/0029-5493(72)90031-3, Vol.
20
,
1972
, pp.
265
-
286
.
8.
Smith
,
S. H.
, “
Analysis of Energy Quantities for Fracture Under Biaxial Stresses
,” presented at the
Conference on Prospects for Fracture Mechanics
,
Delft
,
1974
.
9.
Ueda
,
Y.
,
Ikeda
,
K.
,
Yao
,
T.
,
Aoki
,
M.
,
Yoshie
,
T.
, and
Shirakura
,
T.
, “
Brittle Fracture Initiation Characteristics Under Biaxial Loading
,” in
Fracture 1977
,
Fourth International Conference on Fracture
,
Waterloo, Canada
, Vol.
2
,
Pergamon Press
,
06
1977
, pp.
173
-
182
.
10.
Leevers
,
P. S.
,
Radon
,
J. C.
, and
Culver
,
L. E.
, “
Crack Growth in Panels Under Biaxial Stress
,”
Polymer
 0032-3861, Vol.
17
,
07
1976
, pp.
627
-
632
.
11.
Joshi
,
S. R.
and
Shewchuck
,
J.
, “
Fatigue Crack Propagation in a Biaxial Stress Field
,”
Journal of Experimental Mechanics
, Vol.
10
,
12
1970
, pp.
529
-
533
.
12.
Habètínek
,
J.
, “
Fatigue Strength and Fatigue Failure at Complicated States of Stress
,”
Engineering Fracture Mechanics
 0013-7944, Vol.
8
, No.
4
,
1976
, pp.
677
-
689
.
13.
Christensen
,
R. H.
and
Harmon
,
M. B.
, “
Limitation of Fatigue-Crack Research in the Design of Flight Vehicle Structures
,” in
Fatigue Crack Propagation
, STP 415,
American Society for Testing and Materials
,
Philadelphia
,
1967
, pp.
5
-
23
.
14.
Ogura
,
K.
,
Ohji
,
J.
, and
Ohkubo
,
Y.
, “
Fatigue Crack Growth Under Biaxial Loading
,”
International Journal of Fracture
, Vol.
10
,
1974
, pp.
609
-
610
.
15.
Hopper
,
C. D.
and
Miller
,
K. J.
, “
Fatigue Crack Propagation in Biaxial Stress Fields
,”
Journal of Strain Analysis
 0022-4758, Vol.
12
, No.
1
,
1977
, pp.
23
-
28
.
16.
Roberts
,
R.
and
Pothiraj
,
S.
, “
The Effect of Biaxial Stresses and Combined Stresses on Fatigue and Fracture
,” Paper L8/3, presented at the
Second International Conference on Structural Mechanics in Reactor Technology
,
Berlin
,
09
1973
.
17.
Toor
,
P. M.
, “
On Fracture Mechanics Under Complex Stress
,”
Engineering Fracture Mechanics
 0013-7944, Vol.
7
,
1975
, pp.
321
-
329
.
18.
Zamrick
,
S. Y.
and
Shabara
,
M. A.
, “
The Application of Fracture Mechanics Analysis to Crack Growth Rate in a Biaxial Stress Field
,” in
IVth Inter-American Conference on Materials Technology
,
South West Research Institute
,
Caracas, Venezuela
,
1975
, pp.
472
-
477
.
19.
Pook
,
L. P.
and
Denton
,
K.
, “
Fatigue Crack Growth in Thin Walled Mild Steel Cylinders Loaded in Torsion
,”
International Journal of Fracture Mechanics
 0376-9429, Vol.
8
,
1972
, pp.
118
-
120
.
20.
Adams
,
N. J. I.
, “
Fatigue Crack Growth in Pure Shear
,” Paper V-522A, presented at the
Third International Conference on Fracture
,
Berlin
,
1973
.
21.
Evans
,
W. J.
, “
Deformation and Failure Under Multiaxial Stresses—A Survey of Laboratory Techniques and Experimental Data
,” in
Aeronautical Research Council, Current Papers No. 1306
,
Her Majesty's Stationery Office
,
London
,
1974
.
22.
Brown
,
M. W.
and
Miller
,
K. J.
, “
A Theory for Fatigue Failure Under Multiaxial Stress-Strain Conditions
,”
Proceedings, Institution of Mechanical Engineers
, Vol.
187
,
1973
, pp.
745
-
755
.
23.
Holston
,
A.
 Jr.
, “
A Mixed Mode Crack Tip Finite Element
,”
International Journal of Fracture
, Vol.
12
, No.
6
,
1976
, pp.
887
-
899
.
24.
Mönsch
,
E.
and
Galster
,
D.
, “
A Method for Producing a Defined Uniform Biaxial Tensile Stress Field
,”
British Journal of Applied Physics
 0508-3443, Vol.
14
,
1963
, pp.
810
-
812
.
25.
Johnson
,
A. E.
and
Khan
,
B.
, “
A Biaxial-Stressing Creep Machine and Extensometer
,”
Proceedings, Institute of Mechanical Engineers
, Vol.
180
, Part 3A, 1965–1966, pp.
318
-
323
.
26.
Fessler
,
H.
and
Musson
,
J. K.
, “
A 30-Ton Biaxial Tensile Testing Machine
,”
Journal of Strain Analysis
 0022-4758, Vol.
4
, No.
1
,
1969
, pp.
22
-
26
.
27.
Kelly
,
D. A.
, “
Problems in Crack Testing Under Biaxial Stress Systems
,”
Journal of Strain Analysis
 0022-4758, Vol.
11
, No.
1
,
1976
, pp.
1
-
6
.
28.
Terry
,
G.
, “
The Biaxial Tensile Strain Field from a Conventional Load-Splitting Tree
,”
Strain
,
07
1977
, pp.
110
-
112
.
29.
Pascoe
,
K. J.
and
de Villiers
,
J. W. R.
, “
Low Cycle Fatigue of Steels Under Biaxial Straining
,”
Journal of Strain Analysis
 0022-4758, Vol.
2
, No.
2
,
1967
, pp.
117
-
126
.
30.
Parsons
,
M. W.
and
Pascoe
,
K. J.
, “
Development of a Biaxial Fatigue Testing Rig
,”
Journal of Strain Analysis
 0022-4758, Vol.
10
, No.
1
,
1975
, pp.
1
-
9
.
31.
Lamba
,
H. S.
, “
Non-Proportional Cyclic Plasticity
,” Report 413,
Department of Theoretical and Applied Mechanics, University of Illinois
, Urbana,
1976
.
32.
Charvat
,
I. M. H.
, “
The Development of Testing Methods for Static and Fatigue Crack Propagation Studies Under Biaxial Stress
,” M.Sc. thesis,
University of Cape Town, Republic of South Africa
,
1977
.
33.
Wilson
,
I. H.
and
White
,
D. J.
, “
Cruciform Specimens for Biaxial Fatigue Tests: An Investigation Using Finite-Elements Analysis and Photoelastic-Coating Techniques
,”
Journal of Strain Analysis
 0022-4758, Vol.
6
, No.
1
,
1971
, pp.
27
-
37
.
34.
Smith
,
E. W.
, “
Cyclic-Biaxial Deformation and Fracture of a Steel and a Composite
,” Report Mat/TR-14,
Cambridge University Engineering Department
, United Kingdom,
1974
.
35.
Parsons
,
M. W.
and
Pascoe
,
K. J.
, “
Observations of Surface Deformation, Crack Initiation and Crack Growth in Low-Cycle Fatigue Under Biaxial Stress
,”
Materials Science and Engineering
, Vol.
22
, No.
1
,
1976
, pp.
31
-
50
.
36.
Pook
,
L. P.
and
Holmes
,
R.
, “
Bi-Axial Fatigue Crack Growth Tests
,” Paper 36 in
S.E.E. International Conference on Fatigue Testing and Design
,
City University
,
London
,
1976
.
37.
Dixon
,
J. R.
, “
Stress Distribution and Buckling in Thin Sheets with Central Slits
,” in
Proceedings, 2nd International Conference on Fracture
,
Brighton
,
1979
, pp.
105
-
118
.
This content is only available via PDF.
You do not currently have access to this content.