Abstract

We reconsider standard uniaxial fatigue test data obtained from handbooks. Many S-N curve fits to such data represent the median life and exclude load-dependent variance in life. Presently available approaches for incorporating probabilistic aspects explicitly within the S-N curves have some shortcomings, which we discuss. We propose a new linear S-N fit with a prespecified failure probability, load-dependent variance, and reasonable behavior at extreme loads. We fit our parameters using maximum likelihood, show the reasonableness of the fit using Q-Q plots, and obtain standard error estimates via Monte Carlo simulations. The proposed fitting method may be used for obtaining S-N curves from the same data as already available, with the same mathematical form, but in cases in which the failure probability is smaller, say, 10 % instead of 50 %, and in which the fitted line is not parallel to the 50 % (median) line.

References

1.
U.S. Department of Transportation, Federal Aviation Administration,
2003
, “
MMPDS-01: Metallic Materials Properties Development and Standardization
,” www.knovel.com/(Last accessed 20 March
2012
).
2.
Hobbacher
,
A.
, “
Recommendations for Fatigue Design of Welded Joints and Components
,” International Institute of Welding,
IIW-1823-07 ex XIII-2151r4-07/XV-1254r4-07
, Zone Industrielle Paris Nord II 90, rue des Vanesses, VILLEPINTE, FRANCE,
2008
.
3.
Nelson
,
W.
, “
Fitting of Fatigue Curves with Nonconstant Standard Deviation to Data with Runouts
,”
J. Test. Eval.
, Vol.
12
,
1984
, pp.
69
77
. https://doi.org/10.1520/JTE10700J
4.
Montgomery
,
D. C.
and
Runger
,
G. C.
,
Applied Statistics and Probability for Engineers
, 3rd ed.,
Wiley
,
Singapore
,
2003
.
5.
Hogg
,
R. V.
and
Craig
,
A. T.
,
Introduction to Mathematical Statistics
, 5th ed.,
Pearson Education
,
Singapore
,
1995
.
6.
Shao
,
J.
,
Mathematical Statistics
, 2nd ed.,
Springer
,
New York
,
2003
.
7.
Klein
,
J. P.
, and
Moeschberger
,
M. L.
,
Survival Analysis: Techniques for Censored and Truncated Data
, 2nd ed.,
Springer
,
New York
,
2003
.
8.
Makkonen
,
L.
, “
Bringing Closure to the Plotting Position Controversy
,”
Commun. Stat.: Theory Meth.
, Vol.
37
(
3
),
2008
, pp.
460
467
. https://doi.org/10.1080/03610920701653094
9.
Rambabu
,
D. V.
,
Ranganath
,
V. R.
,
Ramamurty
,
U.
, and
Chatterjee
,
A.
, “
Variable Stress Ratio in Cumulative Fatigue Damage: Experiments and Comparison of Three Models
,”
Proc. Inst. Mech. Eng., Part C
, Vol.
224
,
2009
, pp.
271
282
. https://doi.org/10.1243/09544062JMES1579
10.
Patil
,
N.
,
Mahadevan
,
P.
, and
Chatterjee
,
A.
, “
A Constructive Empirical Theory for Metal Fatigue under Block Cyclic Loading
,”
Proc. R. Soc. London, Ser. A
, Vol.
464
,
2008
, pp.
1161
1179
. https://doi.org/10.1098/rspa.2007.0109
11.
Walker
,
T.
, “
The Effect of Stress Ratio during Crack Propagation and Fatigue for 2024-T3 and 7075-T6 Aluminum
,”
Effects of Environment and Complex Load History on Fatigue Life
,
ASTM STP 462, ASTM International
,
West Conshohocken, PA
,
1970
, pp.
1
14
.
12.
Ling
,
J.
and
Pan
,
J.
, “
A Maximum Likelihood Method for Estimating P-S-N Curves
,”
Int. J. Fatigue
, Vol.
19
(
5
),
1997
, pp.
415
419
. https://doi.org/10.1016/S0142-1123(97)00037-6
13.
Pascual
,
F. G.
, and
Meeker
,
W. Q.
, “
Analysis of Fatigue Data with Runouts based on a Model with Non-constant Standard Deviation and a Fatigue Limit Parameter
,”
J. Test. Eval.
, Vol.
25
(
3
),
1997
, pp.
292
301
. https://doi.org/10.1520/JTE11341J
14.
Xiong
,
J. J.
, and
Shenoi
,
R. A.
, “
Single-point Likelihood Method to Determine a Generalized S-N Surface
,”
Proc. Inst. Mech. Eng., Part C
, Vol.
220
,
2006
, pp.
1519
1529
. https://doi.org/10.1243/09544062JMES127
15.
Zheng
,
X.-L.
,
,
B.
, and
Jiang
,
H.
, “
Determination of Probability Distribution of Fatigue Strength and Expressions of P-S-N Curves
,”
Eng. Fract. Mech.
, Vol.
50
(
4
),
1995
, pp.
483
491
. https://doi.org/10.1016/0013-7944(94)00218-7
16.
Castillo
,
E.
and
Fernández-Canteli
,
A.
,
A Unified Statistical Methodology for Modeling Fatigue Damage
,
Springer
,
New York
,
2009
.
17.
Schneider
,
C. R. A.
and
Maddox
,
S. J.
, “
Best Practice Guide on Statistical Analysis of Fatigue Data
,”
International Institute of Welding
, IIW-XIII-WG1-114-03, Zone Industrielle Paris Nord II 90, rue des Vanesses, VILLEPINTE,
FRANCE
,
2003
.
18.
ASTM E739–91
,
2004
, “
Standard Practice for Statistical Analysis of Linear or Linearized Stress-Life (S-N) and Strain-Life (S-N) Fatigue Data
,”
Annual Book of ASTM Standards
,
ASTM International
,
West Conshohocken, PA.
19.
Boos
,
D. D.
, “
Introduction to the Bootstrap World
,”
Stat. Sci.
, Vol.
18
(
2
),
2003
, pp.
168
174
. https://doi.org/10.1214/ss/1063994971
This content is only available via PDF.
You do not currently have access to this content.