Abstract
Simple cantilever bend testing to assess mechanical descaling of industrial hot-rolled steel rods has been developed and analysed. This test method has no contact damage to the scale, and produces a range of strains along the rod, which always include those for scale behaviour from crack initiation to complete spallation. A series of methods has been used to assess the variation of the plastic strain along the bent rods and the results have been compared with finite element modelling. Using a cyclone scanner for these measurements provides an accurate and efficient testing procedure. To compare with industrial practice, constrained bending around cylinders was also carried out.
Issue Section:
Research Papers
References
1.
Tominaga
, J.
, Wakimoto
, K.
, Mori
, T.
, Murakami
, M.
, and Yoshimura
, T.
, Trans. Iron Steel Inst. Jpn.
, Vol. 22
, No. 8
, 1982
, pp. 646
–656
. https://doi.org/10.2355/isijinternational1966.22.6462.
Stalson
, S. L.
and Hurat
, L. T.
, Wire Wire Prod.
, Vol. 40
, No. 11
, 1965
, pp. 1731–1736, 1765.3.
Sachs
, K.
and Jay
, G. T.
, J. Iron Steel Inst., London
, Vol. 191
, No. 1
, 1959
, pp. 34
–44
.4.
Queiroga
, R. H. B.
, Macedo dos Santos
, R. J.
, and Santos
, D. B.
, Wire J. Int.
, Vol. 28
, No. 10
, 1995
, pp. 56
–63
.5.
Böckenhoff
, H. J.
, Wire Ind.
, Vol. 51
, No. 609
, 1984
, pp. 632
–637
.6.
Bhattacharya
, R.
, Jha
, G.
, Kundu
, S.
, Shankar
, R.
, and Gope
, N.
, Surf. Coat. Technol.
, Vol. 201
, Nos. 3–4
, 2006
, pp. 526
–532
. https://doi.org/10.1016/j.surfcoat.2005.12.0147.
Genève
, D.
, Rouxel
, D.
, Geat
P.
, and Confente
, M.
, Corros. Sci.
, Vol. 52
, No. 4
, 2010
, pp. 1155
–1166
. https://doi.org/10.1016/j.corsci.2009.12.0288.
Hall
, D. J.
, Booth
, S.
, and Evans
, W. T.
, Mater. Sci. Technol.
, Vol. 6
, No. 1
, 1990
, pp. 53
–55
. https://doi.org/10.1179/0267083907901893809.
Nagl
, M. M.
, 1992
, Ph.D. thesis, University of Glamorgan and the National Physical Laboratory (NPL)
, Wales.10.
Nagl
, M. M.
, Evans
, W. T.
, Saunders
S. R. J.
, and Hall
, D. J.
, Mater. Sci. Technol.
, Vol. 8
, No. 11
, 1992
, pp. 1043
–1049
. https://doi.org/10.1179/02670839279040983311.
Nagl
, M. M.
, Evans
, W. T.
, Saunders
, S. R. J.
, and Hall
, D. J.
, Corros. Sci.
, Vol. 35
, Nos. 5–8
, 1993
, pp. 965
–977
. https://doi.org/10.1016/0010-938X(93)90315-812.
Nagl
, M. M.
, Evans
, W. T.
, Hall
, D. J.
, and Saunders
, S. R. J.
, Oxid. Met.
, Vol. 42
, Nos. 5–6
, 1994
, pp. 431
–449
.13.
Huntz
, A. M.
, Piant
, A.
, Lebrun
, J. L.
, and Daghigh
, S.
, Mater. Sci. Eng., A
, Vol. 248
, Nos. 1–2
, 1998
, pp. 44
–55
. https://doi.org/10.1016/S0921-5093(98)00519-X14.
Nicholls
, J. R.
, Evans
, H. E.
, and Saunders
, S. R. J.
, Mater. High Temp.
, Vol. 14
, No. 1
, 1997
, pp. 5
–13
.15.
Yang
, W.
, Li
, Y. H.
, and Sellars
, C. M.
, Ironmaking Steel/making
(Last accessed 12 January 2012
), DOI: https://doi.org/10.1179/1743281211Y.0000000084
This content is only available via PDF.
All rights reserved. This material may not be reproduced or copied, in whole or part, in any printed, mechanical, electronic, film, or other distribution and storage media, without the written consent of ASTM International.
You do not currently have access to this content.