1-20 of 41
Keywords: stainless steel
Close
Sort by
Journal Articles
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Pressure Vessel Technol. December 2011, 133(6): 061209.
Published Online: October 31, 2011
...H. F. Wang; Z. F. Sang; G. E. O. Widera The fabrication of stainless steel tube-to-tubesheet joints of heat exchangers consists of welding after hydraulic expansion. Here, this process is simulated by use of the finite element method, which is carried out in a sequentially decoupled analysis...
Journal Articles
Journal Articles
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Pressure Vessel Technol. August 2011, 133(4): 041207.
Published Online: May 17, 2011
...Yinsheng Li; Kunio Hasegawa; Akira Shibuya; Nathaniel G. Cofie When a flaw is detected in a stainless steel piping system, an evaluation has to be performed to determine its suitability for continued operation. The failure bending moment of the flawed pipe can be predicted by limit load criterion...
Journal Articles
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Pressure Vessel Technol. June 2011, 133(3): 031403.
Published Online: April 4, 2011
... process and load decrease in structure having stress concentration. Test specimens made of SUS304 stainless steel are tested at 550 ° C and the geometry of the semicircular notched plate specimens are changed by diameter size of the circular notch in both of single-notched specimens and double-notched...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Pressure Vessel Technol. April 2011, 133(2): 021403.
Published Online: March 14, 2011
...Jun-Seok Yang; Chi-Yong Park; Nam-Su Huh The present paper addresses the mechanical characteristics of the stainless steel narrow gap weld (NGW) for the leak-before-break (LBB) application to the main loop piping of a nuclear power plant. Recently, in Korea, the connection with the reactor coolant...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Pressure Vessel Technol. April 2011, 133(2): 021401.
Published Online: February 9, 2011
...) was initially used in USC plants and HCM12A (ASME Grade 122 ( 1 ), KA-SUS410J3 in Japanese standard) was subsequently employed to achieve cost reduction by thinning tube or pipe with higher allowable stresses. creep fracture fracture toughness stainless steel welding 17 03 2009 11 09...
Journal Articles
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Pressure Vessel Technol. December 2010, 132(6): 061204.
Published Online: October 14, 2010
...Yinsheng Li; Kunio Hasegawa; Kunio Onizawa; Nathaniel G. Cofie When a flaw is detected in a stainless steel piping system of a nuclear power plant during in-service inspection, the limit load estimation method provided in codes such as ASME Section XI or JSME S NA-1-2008 can be applied to evaluate...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Pressure Vessel Technol. October 2010, 132(5): 051303.
Published Online: August 31, 2010
...K. K. Botros; J. Geerligs; R. J. Eiber Measurements of decompression wave speed in conventional and rich natural gas mixtures following rupture of a high-pressure pipe have been conducted. A high-pressure stainless steel rupture tube (internal diameter = 38.1 mm and 42 m long) has been constructed...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Pressure Vessel Technol. August 2010, 132(4): 041404.
Published Online: July 23, 2010
... R T ) It has been reported that Eq. 11 is in good agreement with the experimental data for SUS304 stainless steel ( 20 ), Cr–Mo–V steel ( 21 ), γ ′ Ni-based superalloys ( 22 ), and high Cr tempered martensite steel ( 23 ). Derivation method of the Q ∗ parameter...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Pressure Vessel Technol. December 2009, 131(6): 061406.
Published Online: October 28, 2009
...M. Turski; M. C. Smith; P. J. Bouchard; L. Edwards; P. J. Withers Application of electronic speckle pattern interferometry (ESPI) is described to measure the spatial variation in monotonic tensile stress-strain properties along “cross-weld” specimens machined from a stainless steel three-pass...
Journal Articles
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Pressure Vessel Technol. April 2009, 131(2): 021209.
Published Online: January 13, 2009
... stainless steel pipes with two symmetrical circumferential flaws. Consequently, it was shown that the proposed method can predict well the plastic collapse stresses for pipes with two flaws. In addition, it is also shown that this method is appropriate to use in fitness-for-service procedures, and higher...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Pressure Vessel Technol. April 2009, 131(2): 021405.
Published Online: December 30, 2008
... needs to be addressed in simulation. In this study, ratcheting tests are conducted on stainless steel 304 under uniaxial, torsional, and combined axial-torsional loading. The ratcheting strain is predicted based on the constitutive theory that incorporates a modified Ohno–Wang kinematic hardening rule...
Journal Articles
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Pressure Vessel Technol. November 2008, 130(4): 041202.
Published Online: August 20, 2008
.... Thus, it is important to optimize the brazing parameters in order to minimize such effects. This paper presents a three-dimensional finite element analysis for determining the residual stresses and thermal deformation of a three layered stainless steel plate-fin structure fabricated by nickel-based...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Pressure Vessel Technol. August 2008, 130(3): 031402.
Published Online: June 6, 2008
...Andrey P. Jivkov; Nicholas P. C. Stevens; Thomas J. Marrow The resistance of polycrystalline materials to intergranular cracking can be influenced by the microstructure. In sensitized stainless steels, for example, the grain boundaries prone to sensitization form paths of low resistance...