Cold bends are frequently required in energy pipelines in order to change the vertical and horizontal orientations of the pipeline route. They are produced by plastically bending a pipe joint in a cold bending machine by creating a series of uniformly spaced incremental bends. This procedure acts to reduce the moment capacity and buckling strain of the pipe, and studying the changes in pipe properties caused by cold bending is valuable in assessing the level of this strength reduction. Accordingly, the initial imperfections and material transformations of five full-scale cold bend pipes were assessed in this research program. The imperfections were measured at several locations around the circumference of the specimens, along the entire bend length. It was determined that the distribution of imperfections was similar in shape to a sine function, and their amplitude ranged from . Tension coupon tests were conducted on the intrados, extrados, and virgin materials of the specimens. It was revealed that the extrados material exhibited an increase in yield strength due to work hardening and that the intrados material demonstrated a reduction in yield strength due to the Bauschinger effect. It was established that the imperfections, and material transformations in the specimens were predominantly unaffected by the incremental-bend magnitude or spacing that was employed during the cold bending procedure.
Skip Nav Destination
Article navigation
Research Papers
Mechanical Properties of Cold Bend Pipes
M. Sen,
M. Sen
Department of Civil and Environmental Engineering,
University of Alberta
, Edmonton, AB, T6G 2G7, Canada
Search for other works by this author on:
J. J. R. Cheng,
J. J. R. Cheng
Department of Civil and Environmental Engineering,
University of Alberta
, Edmonton, AB, T6G 2G7, Canada
Search for other works by this author on:
D. W. Murray,
D. W. Murray
Department of Civil and Environmental Engineering,
University of Alberta
, Edmonton, AB, T6G 2G7, Canada
Search for other works by this author on:
J. Zhou
J. Zhou
TransCanada Pipelines Ltd.
, 450-1st Street Southwest, Calgary, AB, T2P 5H1, Canada
Search for other works by this author on:
M. Sen
Department of Civil and Environmental Engineering,
University of Alberta
, Edmonton, AB, T6G 2G7, Canada
J. J. R. Cheng
Department of Civil and Environmental Engineering,
University of Alberta
, Edmonton, AB, T6G 2G7, Canada
D. W. Murray
Department of Civil and Environmental Engineering,
University of Alberta
, Edmonton, AB, T6G 2G7, Canada
J. Zhou
TransCanada Pipelines Ltd.
, 450-1st Street Southwest, Calgary, AB, T2P 5H1, CanadaJ. Pressure Vessel Technol. May 2008, 130(2): 021708 (6 pages)
Published Online: May 13, 2008
Article history
Received:
January 15, 2007
Revised:
December 12, 2007
Published:
May 13, 2008
Citation
Sen, M., Cheng, J. J. R., Murray, D. W., and Zhou, J. (May 13, 2008). "Mechanical Properties of Cold Bend Pipes." ASME. J. Pressure Vessel Technol. May 2008; 130(2): 021708. https://doi.org/10.1115/1.2892034
Download citation file:
Get Email Alerts
Cited By
The Behavior of Elbow Elements at Pure Bending Applications Compared to Beam and Shell Element Models
J. Pressure Vessel Technol (February 2025)
Related Articles
Influence of Yield-to-Tensile Strength Ratio on Failure Assessment of Corroded Pipelines
J. Pressure Vessel Technol (November,2005)
Effect of Lüders Plateau on Fracture Response and Toughness of Pipelines Subject to Extreme Plastic Bending
J. Pressure Vessel Technol (October,2011)
Critical Buckling Strain Equations for Energy Pipelines—A Parametric Study
J. Offshore Mech. Arct. Eng (August,2006)
A Critical Reexamination of Classical Metal Plasticity
J. Appl. Mech (January,2002)
Related Proceedings Papers
Related Chapters
Final Report on Determining the Yield Strength of In-Service Pipe
Determining the Yield Strength of In-Service Pipe (CRTD Vol. 57)
Final Report
Applications Guide for Determining the Yield Strength of In-Service Pipe by Hardness Evaluation: Final Report
Section XI Flaw Acceptance Criteria and Evaluation Using Code Procedures
Companion Guide to the ASME Boiler & Pressure Vessel Codes, Volume 2, Sixth Edition