A noncontact, laser-optic based laser ultrasonic technique referred to as the thermo-acousto-photonic nondestructive evaluation (TAP-NDE) was utilized to investigate bond integrity and localized stiffening due to an attached wire stent on small-diameter polymeric medical tubing. Laser-generated interrogating ultrasonic waves in the tubing were detected by use of a fiber-tip interferometer (FTI) and a continuous wave HeNe laser. The time-frequency analysis of the generated dispersive waves was performed using the Gabor wavelet transform (GWT) that effectively decomposed the digitized waveguide mode enabling identification of defect characteristic frequency tendencies. Three different bond defects were evaluated: tensile pull, needle puncture, and crease. These induced flaws represent possible manufacturing defects such as de-bond, potential leak sources, and geometry irregularities. The frequency tendencies were found to uniquely identify each bond defect. Frequency tendencies were also found to uniquely identify localized stiffening due to an attached wire stent proving that this technique can unambiguously identify propagation modes from among nonpropagation modes or vibrations. These findings demonstrate the utility of TAP-NDE and the GWT for quality inspection of small-diameter polymeric medical tubing.
Skip Nav Destination
e-mail: ssuh@mengr.tamu.edu
Article navigation
August 2002
Technical Papers
Laser-Optic Evaluation for Bond Quality of Polymeric Medical Tubing
Kent D. Harms,
Kent D. Harms
Photomechanics Laboratory, Department of Mechanical Engineering, Texas A&M University, College Station, TX 77843-3123
Search for other works by this author on:
C. Steve Suh
e-mail: ssuh@mengr.tamu.edu
C. Steve Suh
Photomechanics Laboratory, Department of Mechanical Engineering, Texas A&M University, College Station, TX 77843-3123
Search for other works by this author on:
Kent D. Harms
Photomechanics Laboratory, Department of Mechanical Engineering, Texas A&M University, College Station, TX 77843-3123
C. Steve Suh
Photomechanics Laboratory, Department of Mechanical Engineering, Texas A&M University, College Station, TX 77843-3123
e-mail: ssuh@mengr.tamu.edu
Contributed by the Pressure Vessels and Piping Division for publication in the JOURNAL OF PRESSURE VESSEL TECHNOLOGY. Manuscript received by the PVP Division, January 20, 2001; revised manuscript received April 15, 2002. Associate Editor: S. Y. Zamrik.
J. Pressure Vessel Technol. Aug 2002, 124(3): 283-292 (10 pages)
Published Online: July 26, 2002
Article history
Received:
January 20, 2001
Revised:
April 15, 2002
Online:
July 26, 2002
Citation
Harms , K. D., and Suh, C. S. (July 26, 2002). "Laser-Optic Evaluation for Bond Quality of Polymeric Medical Tubing ." ASME. J. Pressure Vessel Technol. August 2002; 124(3): 283–292. https://doi.org/10.1115/1.1484116
Download citation file:
Get Email Alerts
Cited By
Surface Strain Measurement for Non-Intrusive Internal Pressure Evaluation of A Cannon
J. Pressure Vessel Technol
The Upper Bound of the Buckling Stress of Axially Compressed Carbon Steel Circular Cylindrical Shells
J. Pressure Vessel Technol (December 2024)
Crack Growth Prediction Based on Uncertain Parameters Using Ensemble Kalman Filter
J. Pressure Vessel Technol (December 2024)
Defect Detection of Polyethylene Gas Pipeline Based on Convolutional Neural Networks and Image Processing
J. Pressure Vessel Technol
Related Articles
A Baseline and Vision of Ultrasonic Guided Wave Inspection Potential
J. Pressure Vessel Technol (August,2002)
Laser Array/EMAT Ultrasonic Measurement of the Penetration Depth in a Liquid Weld Pool
J. Manuf. Sci. Eng (February,2000)
Overview of the Impact of Ultrasonic Examination Performance Demonstration on the ASME Boiler and Pressure Vessel Code
J. Pressure Vessel Technol (August,2002)
Special Issue on the Nondestructive Evaluation of Pipeline and Vessel Structures
J. Pressure Vessel Technol (August,2005)
Related Proceedings Papers
Related Chapters
Conclusion
Biopolymers Based Micro- and Nano-Materials
Examination
Process Piping: The Complete Guide to ASME B31.3, Third Edition
Introduction
Computer Vision for Structural Dynamics and Health Monitoring