During the last five years, high-strength steels with yield strengths in the range 420 to 500 MPa have attracted considerable interest within the offshore industry, primarily due to the potential for weight saving and reduction in volume of weld metal through the use of reduced section thicknesses. With respect to chemical composition these steels are developed following much the same philosophoy as for the modern normalized structural steels. Due to the increased stress level in these higher strength steels, it is anticipated that brittle fracture initiation occurring in the coarse-gained HAZ will be more critical for these steels than for the lower strength normalized grades. The objective of this paper is to present the results from several experimental investigations carried out at VERITEC during the last five years to study the factors affecting the crack tip opening displacement (CTOD) fracture toughness of the heat-affected zone (HAZ) in structural steels in the yield strength range 420–500 MPa. Typical CTOD fracture toughnesses of the HAZ in normalized 350-MPa yield strength steels used in offshore structures are also presented for comparison. The results of the investigations confirm that the same chemical compositional factors which are known to influence the HAZ fracture toughness of normalized steels are also important for the 420–500-MPa yield strength steels. It is demonstrated that the width of the HAZ is important for the initiation of brittle fracture of pop-in and that this width must exceed a certain minimum value for such events to occur. For different welding conditions, i.e., welding currents/travel speeds, the width of the coarse-grained HAZ changes considerably along the periphery of the weld bead. Thus, one may obtain widely differing results depending on the exact fatigue pre-crack placement. In addition to the weld cooling time between 800 and 500° C, Δt8/5 and the retention time above 1000° C during the weld thermal cycle, RT1000, the welding process and consumables also exert a strong influence on the CTOD values of the coarse-grained HAZ.
Skip Nav Destination
Article navigation
February 1993
Research Papers
Heat-Affected Zone Fracture Toughness of 420–500-MPa Yield Strength Steels: Effects of Chemical Composition and Welding Conditions
J. P. Tronskar
J. P. Tronskar
Det Norske Veritas Industri Norge as (VERITEC), Ho̸vik, Norway
Search for other works by this author on:
J. P. Tronskar
Det Norske Veritas Industri Norge as (VERITEC), Ho̸vik, Norway
J. Offshore Mech. Arct. Eng. Feb 1993, 115(1): 66-75 (10 pages)
Published Online: February 1, 1993
Article history
Received:
November 13, 1991
Revised:
August 6, 1992
Online:
June 12, 2008
Citation
Tronskar, J. P. (February 1, 1993). "Heat-Affected Zone Fracture Toughness of 420–500-MPa Yield Strength Steels: Effects of Chemical Composition and Welding Conditions." ASME. J. Offshore Mech. Arct. Eng. February 1993; 115(1): 66–75. https://doi.org/10.1115/1.2920092
Download citation file:
Get Email Alerts
Cited By
Time-dependent wave motion in a running stream due to initial disturbances in Magnetohydrodynamics
J. Offshore Mech. Arct. Eng
The autonomous urban passenger ferry milliAmpere2: Design and testing
J. Offshore Mech. Arct. Eng
Numerical Analysis of the Effect of Tunnel Hydrofoil—Stern Flap on the Motion Stability of a Double M-Craft in Regular Waves
J. Offshore Mech. Arct. Eng (August 2025)
On the Performance of a Data-Driven Backward Compatible Physics-Informed Neural Network for Prediction of Flow Past a Cylinder
J. Offshore Mech. Arct. Eng (August 2025)
Related Articles
Notch-Ductility Transition of Structural Steels of Various Yield Strengths
J. Eng. Ind (February,1972)
The Effective Utilization of Yield Strength
J. Eng. Ind (November,1971)
Fatigue-Crack Propagation in Steels of Various Yield Strengths
J. Eng. Ind (November,1971)
An Analytical Assessment of the Effects of Residual Stresses and Fracture Properties on Service Performance of Various Weld Repair Processes
J. Pressure Vessel Technol (November,1981)
Related Proceedings Papers
Related Chapters
Compromise between Tensile and Fatigue Strength
New Advanced High Strength Steels: Optimizing Properties
Dismantling
Decommissioning Handbook
Multiscale Methods for Lightweight Structure and Material Characterization
Advanced Multifunctional Lightweight Aerostructures: Design, Development, and Implementation