1-20 of 27
Keywords: stainless steel
Close
Sort by
Journal Articles
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Manuf. Sci. Eng. January 2023, 145(1): 011001.
Paper No: MANU-22-1038
Published Online: September 26, 2022
... when depositing multiple friction surfacing layers, whether for repair, remanufacturing, or new part creation using this solid-state metal additive manufacturing process. In this study, 10-mm-diameter 304L stainless steel rods were used to create up to five layers of 40-mm-long coatings on 304L...
Journal Articles
Journal Articles
Journal Articles
Journal Articles
Publisher: ASME
Article Type: Technical Briefs
J. Manuf. Sci. Eng. December 2011, 133(6): 064501.
Published Online: December 21, 2011
... compressive loads, while also allowing full field strain measurements of the specimen using digital imaging methods. Thin brass and stainless steel sheet metal specimens with thicknesses on the order of 10–100 μ m were tested using the microwedge device. Experimental results show that the device can be used...
Journal Articles
Journal Articles
Journal Articles
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Manuf. Sci. Eng. December 2009, 131(6): 061009.
Published Online: December 3, 2009
... of high tensile strength alloys such as stainless steel 321, Inconel 625, and Ti–3Al–2.5V. The proposed forming technology is based on the utilization of high pressure developed in liquid flowing through a tubular work piece. This pressure results from superposition of compression waves generated...
Journal Articles
Journal Articles
Publisher: ASME
Article Type: Technical Briefs
J. Manuf. Sci. Eng. October 2009, 131(5): 054503.
Published Online: October 1, 2009
...Xiangqun Zhu; Ming Zhou; Qixun Dai; Gary J. Cheng In order to study the deformation mechanisms during ultrahigh strain rate deformation of face centered cubic metals, laser shock peening of a 304L stainless steel is systematically investigated. Two deformation modes—microtwins and microbands...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Manuf. Sci. Eng. October 2009, 131(5): 051008.
Published Online: September 8, 2009
... due to the physical/mechanical properties of the material or from an effect purely related to the processing parameters. We investigated this problem spanning a range of process parameters for deposition and using three different material powders, namely, an AISI 410 grade stainless steel, AISI 316L...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Manuf. Sci. Eng. August 2009, 131(4): 041003.
Published Online: July 7, 2009
... and modeling of pressure welding (solid state bonding) process are investigated, specifically for bonding of thin sheet metals. The effects of material type (e.g., copper, nickel, and stainless steel) and initial plate thickness ( 51 – 254 μ m ) as well as process conditions (e.g., welding pressure...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Manuf. Sci. Eng. December 2008, 130(6): 061010.
Published Online: November 4, 2008
...Xudong Cheng; Xiaochun Li This paper presents a new method to embed microthin film sensors into metallic structures by diffusion bonding. The experiments were carried out using AISI 304 stainless steel substrates with a bonding temperature of 800 ° C and a pressure of 4 MPa, which the developed...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Manuf. Sci. Eng. August 2008, 130(4): 041017.
Published Online: July 22, 2008
... the forming of microfeatures in Type 304 stainless steel by using the coining process. Experimental work was performed to study the effects of workpiece thickness, preform shape, grain size, and feature size on the formation of features ranging from 320 μ m to 800 μ m . It was found that certain preform...
Journal Articles
Publisher: ASME
Article Type: Special Section: Micromanufacturing
J. Manuf. Sci. Eng. June 2008, 130(3): 031107.
Published Online: May 6, 2008
... on the outer surface alone. Their finishing performance, evaluated through the experiments using SUS304 stainless steel tubes, shows their applicability to magnetic abrasive finishing. Use of the composite of plasma sprayed iron particles, sieved to remove particles larger than 75 μ m...
Journal Articles
Publisher: ASME
Article Type: Technical Papers
J. Manuf. Sci. Eng. December 2007, 129(6): 1028–1034.
Published Online: March 13, 2007
...Liang Wang; Sergio Felicelli A three-dimensional finite element model was developed to predict the temperature distribution and phase transformation in deposited stainless steel 410 (SS410) during the Laser Engineered Net Shaping (LENS™) rapid fabrication process. The development of the model...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Manuf. Sci. Eng. October 2007, 129(5): 868–873.
Published Online: January 31, 2007
...L. Casamichele; F. Quadrini; V. Tagliaferri The present work is an experimental investigation on the laser forming process of aluminum alloy and stainless-steel thin sheets. A high-power diode laser (HPDL) with a nonsymmetric spot configuration was employed at medium and low scanning rates...
Journal Articles
Publisher: ASME
Article Type: Technical Briefs
J. Manuf. Sci. Eng. May 2006, 128(2): 606–610.
Published Online: October 6, 2005
...Rachid M’Saoubi; Hariharan Chandrasekaran Cutting tool temperature distribution was mapped using the infrared-charge-coupled device technique during machining of carbon steel SS2511 ( ∼ AISI 3115) and stainless steel AISI 316L under oblique cutting conditions with chip breaker geometry inserts...