In this paper, a dynamic model that considers the vibrations of both the workpiece and fixture elements in order to accurately predict the friction damping over a wide range of clamping forces has been developed. The model is established based on the theory of variational inequality and solved via a nonlinear FEM. It is shown that the model is capable of predicting the system dynamics over a wide range of clamping forces. It is also demonstrated that the increasing then decreasing trend of the damping ratio caused by “interface locking” is due to the relative velocity change at the contact interface. With multiple contact interfaces, the “locking” occurs sequentially. Finally, the model is used to study the influence of friction damping on machining process stability.
Issue Section:
Technical Papers
1.
Den Hartog, J. P., 1956, Mechanical Vibrations, 4th edition, McGraw-Hill, New York.
2.
Earles
, S. W. E.
, and Williams
, E. J.
, 1972
, “A Linearized Analysis for Frictionally Damped Systems
,” J. Sound Vib.
, 24
, pp. 445
–458
.3.
Mindlin, R. D., Mason, W. P., Osmer, T. F., and Deresiewicz, H., 1951, “Effects of an Oscillating Tangential Force on the Contact Surface of Elastic Spheres,” Proceedings of 1st US National Congress of Applied Mechanics, pp. 203–208.
4.
Johnson
, K. L.
, 1961
, “Energy Dissipation at Spherical Surfaces in Contact Transmitting Oscillating Forces
,” J. Mech. Eng. Sci.
, 3
, pp. 362
–368
.5.
Goodman
, L. E.
, and Brown
, C. B.
, 1962
, “Energy Dissipation in Contact Friction: Constant Normal and Cyclic Tangential Loading
,” ASME J. Appl. Mech.
, 29
, pp. 17
–22
.6.
Yang
, B. D.
, and Menq
, C. H.
, 1997
, “Modeling of Friction Contact and Its Application to the Design of Shroud Contact
,” ASME J. Eng. Gas Turbines Power
, 119
, pp. 958
–963
.7.
Griffin
, J. H.
, Wu
, W. T.
, and El-Aini
, Y.
, 1998
, “Friction Damping of Hollow Airfoils: Part 1-Theoretical Development
,” ASME J. Eng. Gas Turbines Power
, 120
, pp. 120
–125
.8.
Shiau
, T. N.
, Rao
, J. S.
, Yu
, Y. D.
, and Choi
, S. T.
, 1998
, “Steady-state Response and Stability of Rotating Composite Blades with Frictional Damping
,” ASME J. Eng. Gas Turbines Power
, 120
, pp. 131
–139
.9.
Aiken, I. D., and Kelly, J. M., 1988, “Experimental Study of Friction Damping for Steel Frame Structures,” Hara et al. eds., ASME Damping, pp. 95–100.
10.
Fang
, B.
, DeVor
, R. E.
, and Kapoor
, S. G.
, 2001
, “An Elastodynamic Model of Frictional Contact and Its Influence on the Dynamics of a Workpiece–Fixture System
,” ASME J. Manuf. Sci. Eng.
, 123
, pp. 481
–489
.11.
Duvaut, G., and Lions, J. L., 1976, Inequalities in Mechanics and Physics, Springer-Verlag.
12.
Martins
, J. A. C.
, and Oden
, J. T.
, 1983
, “A Numerical Analysis of a Class of Problems in Elastodynamics with Friction
,” Comput. Methods Appl. Mech. Eng.
, 40
, pp. 327
–360
.13.
Oden
, J. T.
, and Martins
, J. A. C.
, 1985
, “Models and Computational Methods for Dynamic Friction Phenomena
,” Comput. Methods Appl. Mech. Eng.
, 52
, pp. 527
–634
.14.
Fang, B., 2001, “Workpiece-Fixture Frictional Contact and Its Influence on Machining Performance,” PhD thesis, University of Illinois at Urbana-Champaign.
15.
Babuska
, I.
, and Yu
, D.
, 1987
, “Asymptotically Exact a Posteriori Error Estimator for the Biquadratic Elements
,” Finite Elem. Anal. Design
, 3
, pp. 341
–354
.16.
Haber, R. B., and Shephard, M. S., 1980, “A General Two-Dimensional Graphical Finite Element Pre-processor Utilizing Discrete Transfinite Mappings,” Technical report, Cornell University, May.
17.
Williams
, D.
, 1960
, “Methods of Damping Out Bending Vibration of Beam-Like Structures by Dry (or Coulomb) Friction
,” J. Mech. Eng. Sci.
, 2
, pp. 77
–87
.18.
Fu
, H. J.
, DeVor
, R. E.
, and Kapoor
, S. G.
, 1984
, “A Mechanistic Model for Prediction of the Force System in Face Milling Operations
,” ASME J. Eng. Ind.
, 106
, pp. 81
–88
.19.
Jayaram, S., 1996, “Stability and Vibration Analysis of Turning and Face Milling Process,” PhD thesis, University of Illinois at Urbana-Champaign.
20.
Minis
, I.
, and Yanushevsky
, R.
, 1993
, “A New Theoretical Approach for the Prediction of Machine Tool Chatter in Milling
,” ASME J. Eng. Ind.
, 115
, pp. 1
–8
.Copyright © 2002
by ASME
You do not currently have access to this content.
