Skip Nav Destination
Issues
Research Papers
Interpretation of Material Hardness, Stress Ratio, and Crack Size Effects on the ΔKth of Small Cracks Based on Crack Closure Measurement
J. ASTM Int.. April 2005, 2(4): 1–15.
doi: https://doi.org/10.1520/JAI11990
Analysis of Roughness-Induced Crack-Tip Shielding in Terms of Size Ratio Effect
J. ASTM Int.. April 2005, 2(4): 1–15.
doi: https://doi.org/10.1520/JAI11997
Influence of Crack-Surface Oxidation on Creep-Fatigue Crack Behavior of 1Cr- and 10Cr-Steels
J. ASTM Int.. April 2005, 2(4): 1–16.
doi: https://doi.org/10.1520/JAI12002
Temperature Dependent Fracture Toughness of a Single Crystal Nickel Superalloy
J. ASTM Int.. April 2005, 2(4): 1–13.
doi: https://doi.org/10.1520/JAI12005
Improvements in the Measurement of Cut Protection Performance: Revisions to ASTM F 1790
J. ASTM Int.. April 2005, 2(4): 1–5.
doi: https://doi.org/10.1520/JAI12099
Revised Interlaboratory Study of Sweating Thermal Manikins Including Results from the Sweating Agile Thermal Manikin
J. ASTM Int.. April 2005, 2(4): 1–13.
doi: https://doi.org/10.1520/JAI12109
A Study on the Puncture Resistance of Rubber Materials Used in Protective Clothing
J. ASTM Int.. April 2005, 2(4): 1–14.
doi: https://doi.org/10.1520/JAI12147
Effect of Adjuvant on the Efficacy of Glyphosate Applied at Different Times of Day
J. ASTM Int.. April 2005, 2(4): 1–7.
doi: https://doi.org/10.1520/JAI12156
A Novel Water Conditioning Adjuvant for Use with Formulated and Nonformulated Glyphosate
J. ASTM Int.. April 2005, 2(4): 1–6.
doi: https://doi.org/10.1520/JAI12157
Predicted Deposition Variability Due to Fluctuations in Release Height and Drop Size Distribution
ME Teske, HW Thistle, RC Reardon, G Cormier, P Amirault, DC Davies, R Scott Cameron, G Dorr, AJ Hewitt, JR Brown, MY LeClerc, A Karipot
J. ASTM Int.. April 2005, 2(4): 1–11.
doi: https://doi.org/10.1520/JAI12164
Comparison of Abscission Spray Application Practices for Mechanical Harvesting of Oranges
J. ASTM Int.. April 2005, 2(4): 1–13.
doi: https://doi.org/10.1520/JAI12167
Evaluation of Quartz Residue on Cassette Interiors of AIHA Proficiency Samples
J. ASTM Int.. April 2005, 2(4): 1–6.
doi: https://doi.org/10.1520/JAI12229
Infrared Analysis of Respirable Coal Mine Dust for Quartz: Thirty-Five Years
J. ASTM Int.. April 2005, 2(4): 1–13.
doi: https://doi.org/10.1520/JAI12231
Use of HMA Stiffness Results as a Referee Test in Indiana
J. ASTM Int.. April 2005, 2(4): 1–6.
doi: https://doi.org/10.1520/JAI12261
Utilization of an Asphalt Pavement Analyzer for Hot Mix Asphalt Laboratory Mix Design
J. ASTM Int.. April 2005, 2(4): 1–25.
doi: https://doi.org/10.1520/JAI12268
Inhibitors for Reducing Hydrogen Ingress During Corrosion of Zirconium Alloys
J. ASTM Int.. April 2005, 2(4): 1–19.
doi: https://doi.org/10.1520/JAI12422
Separation of Overlapping Processes from TGA Data and Verification by EGA
J. ASTM Int.. April 2005, 2(4): 1–12.
doi: https://doi.org/10.1520/JAI12795
In-Situ Studies of the Oxide Film Properties on BWR Fuel Cladding Materials
J. ASTM Int.. April 2005, 2(4): 1–16.
doi: https://doi.org/10.1520/JAI12820
Recovery and Quantification of Mycobacterium Immunogenum DNA from Metalworking Fluids Using Dual-Labeled Probes
J. ASTM Int.. April 2005, 2(4): 1–9.
doi: https://doi.org/10.1520/JAI12840
Review of Deformation Mechanisms, Texture, and Mechanical Anisotropy in Zirconium and Zirconium Base Alloys
J. ASTM Int.. April 2005, 2(4): 1–26.
doi: https://doi.org/10.1520/JAI12945
Water Vapor Transmission Measurement and Significance of Corrections
J. ASTM Int. (September 2007)
A Prospective Study of Injuries in NCAA Intercollegiate Ice-Hockey Goaltenders
J. ASTM Int. (March 2009)
Stabilization of Suspension Concentrate Formulations via Specialized Double-comb Polymers
J. ASTM Int. (June 2009)
Correlation Between Charpy Absorbed Energy Using 2 mm and 8 mm Strikers
J. ASTM Int. (October 2011)
