A need for higher packaging density and functionality has increased the use of new packaging technologies, which has also caused demand for higher interconnect densities on printed circuit boards (PCBs). Sequential build-up (SBU) processes can be used to meet these demands. In the SBU process, additional dielectric and conductor layers are formed on a core board, which is typically made of FR-4. Microvias are formed on these layers to achieve an electrical connection between them and the core board. Resin-coated copper foil (RCC) is the most widely used dielectric layer in the SBU process. The effect of RCC on the reliability of flip chip joints with anisotropically conductive adhesive film (ACF) was studied. Two substrates were used. The difference between the substrates was RCC laminated on the other substrate. The reliability of the test samples was studied using a temperature cycling test and a constant humidity test. The reliability of the substrate with the RCC was found to be better in both tests. Failure mechanisms were studied after the tests, using optical and scanning electron microscopes. After the temperature cycling, several of the test samples made with two highest bonding pressures showed delamination, which has probably caused the failures. In addition, failures occurred during the changes in the test temperature. These were probably caused by warping of the flip chip package. No delamination was found in the test samples with the lowest pressure. The failures in these series were probably caused by relaxation of the adhesive matrix and by too low deformation of the conductive particles. Several cracks had formed on the FR-4 substrates without the RCC during the temperature cycling. In addition, air bubbles were found in the test samples with the FR-4 substrates without the RCC. Since RCC is a pure resin system, it has a high coefficient of thermal expansion, which may cause problems, especially when large components are attached to it. However, in this study, the RCC was found to increase the reliability of the flip chip joints made with ACF during both temperature cycling and constant humidity testing.
Skip Nav Destination
e-mail: laura.frisk@tut.fi
Article navigation
September 2007
Technical Papers
Effect of RCC on the Reliability of Adhesive Flip Chip Joints
Laura K. Frisk,
Laura K. Frisk
Institute of Electronics,
e-mail: laura.frisk@tut.fi
Tampere University of Technology
, P.O. Box 692, 33101 Tampere, Finland
Search for other works by this author on:
Kati H. Kokko
Kati H. Kokko
Institute of Electronics,
Tampere University of Technology
, P.O. Box 692, 33101 Tampere, Finland
Search for other works by this author on:
Laura K. Frisk
Institute of Electronics,
Tampere University of Technology
, P.O. Box 692, 33101 Tampere, Finlande-mail: laura.frisk@tut.fi
Kati H. Kokko
Institute of Electronics,
Tampere University of Technology
, P.O. Box 692, 33101 Tampere, FinlandJ. Electron. Packag. Sep 2007, 129(3): 260-265 (6 pages)
Published Online: October 27, 2006
Article history
Received:
January 11, 2006
Revised:
October 27, 2006
Citation
Frisk, L. K., and Kokko, K. H. (October 27, 2006). "Effect of RCC on the Reliability of Adhesive Flip Chip Joints." ASME. J. Electron. Packag. September 2007; 129(3): 260–265. https://doi.org/10.1115/1.2753909
Download citation file:
Get Email Alerts
Cited By
Enhancing Mechanical Reliability of Silver-Sintered Joints With Copper Nanowires in High-Power Electronic Devices
J. Electron. Packag (December 2024)
Special Issue on InterPACK2023
J. Electron. Packag (December 2024)
Impact of Encapsulated Phase Change Material Additives for Improved Thermal Performance of Silicone Gel Insulation
J. Electron. Packag (December 2024)
Related Articles
Various Adhesives for Flip Chips
J. Electron. Packag (March,2005)
Thermal Cycling Reliability and Delamination of Anisotropic Conductive Adhesives Flip Chip on Organic Substrates With Emphasis on the Thermal Deformation
J. Electron. Packag (June,2005)
Process Modeling and Thermal/Mechanical Behavior of ACA/ACF Type Flip-Chip Packages
J. Electron. Packag (December,2001)
Related Proceedings Papers
Related Chapters
Compressive Deformation of Hot-Applied Rubberized Asphalt Waterproofing
Roofing Research and Standards Development: 10th Volume
Concluding Remarks and Future Work
Ultrasonic Welding of Lithium-Ion Batteries
Understanding the Problem
Design and Application of the Worm Gear